Anchor-Seal Platinum Series RTV-2 Silicone Rubber
Two-component addition cured silicone, ideal for casting epoxy, polyester, polyurethane and other plastic parts. Deep section cure as needed for electrical potting, encapsulating and casting; prototype molds to special effect silicones for animatronics and prosthetics.

Product
Base
(Activator)

Shore A
Hardness
(+ / -4)
1 day

Shore A
Hardness
(+ / -4)
3 day

Tear
Resistance (ppi)
ASTM D624
Die B

Tensile Strength
(psi)
ASTM D412

Elongation
(%)
ASTM D412

Mixed
Viscosity
(CPS)

MSDS Sheets: P-10 Base, P-10 Activator			Special Effect Use - Figurine Castings, Complex Shaped Items and Animatronic Skin Systems.
P-10 * Translucent (Clear)	10	10	75 +/- 25	350 +/- 50	450 +/- 50	10,000 - 25,000

P-17

White

(Black)

27 +/- 3

495 +/- 30

150 +/- 20

20,000 - 25,000

MSDS Sheet: P17 Base, P-17 Activator

Electrical Applications - Potting and Encapsulation

MSDS Sheets: P-44 Option 2 Base, P-44 Option 2 Activator			Prototype - Economical, Clear for Visual Inspection
P-44 Option 2 Translucent (Clear)	42	42	120 +/- 20	600 +/- 50	250 +/- 25	50,000 - 60,000

P-45

Off White
(Reddish Brown)

160 +/- 15

800 +/- 50

275 +/- 25

40,000 - 55,000

MSDS Sheets: P-45 Base, P-45 Activator

Prototype - Dimensionally Stable, High Knotty Tear, High Modulus, Excellent Part Release, Low Viscosity

MSDS Sheets: P-50 Base, P-50 Activator			Prototype - Chemical Release, Chemical Resistance, High Strength w/ Low Shrinkage - PU Foam and Self Supporting Mold Applications
P-50 Tan (Green)	52	54	70 +/- 10	750 +/- 50	200 +/- 25	70,000 - 90,000

MSDS Sheets: P-60 Base, P-60 Activator			Prototype - High Durometer, High Modulus, Heat Resistance, Epoxy and Polyurethane
P-60 Tan (Blue)	58	62	75 +/- 10	900 +/- 90	200 +/- 25	95,000 - 120,000

MSDS Sheets: P-90 Base, P-90 Activator			Sculpting, Foundry, Amusement Parks - Low Specific Gravity, Exceptional Flexibility and Tear Resistance - Excellent Detail Registration
P-90 * White (Red)	32	35	125 +/- 10	600 +/- 50	600 +/- 50	40,000 - 55,000

MSDS Sheets: P-125 Base, P-125 Activator			Prototype - Clear for Visual Inspection
P-125 Translucent (Clear)	40	40	90 +/- 15	700 +/- 50	250 +/- 50	90,000 - 110,000

MSDS Sheets: XP-643 Base, XP-643 Activator			Prototype - Good Physical Strength, Moderate Hardness, High Elongation w/ Superb Physical Properties
XP-643 Off White (Blue)	40	44	140 +/- 10	725 +/- 50	700 +/- 25	25,000 - 35,000

MSDS Sheets: P-FDA Base, P-FDA Activator			Designed for mold making where FDA requirements are needed eg, repeated food contact, making candy. Not for medical use inside the human body.
P-FDA White (Clear)	37	37	110	850	360	88000

Specialty Type Products

MR-15	Mold release for GI Series and Platinum series, prevents bonding of Silicone to itself

GI Thinner	Lowers viscosity and can softens the cured RTV. Water clear, non-reactive silicone fluid for use with GI or Platinum Series

Additional Silicone's Inc products available upon request.

All activators are available in clear.
Standard Tin and Platinum Series mix ratio is 10 - 1 by weight, excluding P-17 Black, P-17 Black is 1:1.
All Tin Series products have a minimum of 6 month shelf life.
Tin Series products cure in 16-24 hours @ 75F.

Mixing ratio is 10 parts of Base to 1 part of Activator by weight, excluding P-17. P-17 as shown is a 1:1 ratio. Deviations from
the specified mix ratio will cause changes in the physical properties. Choose a container with a volume that is three to four times
greater than that of the rubber. Weigh the components carefully and mix thoroughly while simultaneously scraping the sides
and bottom of the container to insure that there is no unmixed portion. Place the container in a vacuum chamber and
deaerate at 28 to 29 inches of mercury vacuum until the mass of rubber rises and then collapses. Remove the mixed rubber
and carefully pour over mold, MR-15 is recommended for GI and Platinum molds.

* Translucent Base Available