Anchor-Seal Platinum Series RTV-2 Silicone Rubber
Two-component addition cured silicone, ideal for casting epoxy, polyester, polyurethane and other plastic parts. Deep section cure as needed for electrical potting, encapsulating and casting; prototype molds to special effect silicones for animatronics and prosthetics.

Phone: (800) 669-5217

PDF
Download
Product
Base
(Activator)
Shore A
Hardness
(+ / -4)
1 day
Shore A
Hardness
(+ / -4)
3 day
Tear
Resistance (ppi)
ASTM D624
Die B
Tensile Strength
(psi)
ASTM D412
Elongation
(%)
ASTM D412
Mixed
Viscosity
(CPS)
P-10 *
Translucent
(Clear)
10 10 75 +/- 25 350 +/- 50 450 +/- 50 10,000 - 25,000
MSDS Sheets: P-10 Base, P-10 Activator Special Effect Use - Figurine Castings, Complex Shaped Items and Animatronic Skin Systems.
Anchorseal

P-17

White

(Black)

50 50 27 +/- 3 495 +/- 30 150 +/- 20 20,000 - 25,000
MSDS Sheet: P17 Base, P-17 Activator Electrical Applications - Potting and Encapsulation
Anchorseal
P-44 Option 2
Translucent
(Clear)
42 42 120 +/- 20 600 +/- 50 250 +/- 25 50,000 - 60,000
MSDS Sheets: P-44 Option 2 Base, P-44 Option 2 Activator Prototype - Economical, Clear for Visual Inspection
Anchorseal

P-45

Off White
(Reddish Brown)

44 45 160 +/- 15 800 +/- 50 275 +/- 25 40,000 - 55,000
MSDS Sheets: P-45 Base, P-45 Activator Prototype - Dimensionally Stable, High Knotty Tear, High Modulus, Excellent Part Release, Low Viscosity
Anchorseal
P-50
Tan
(Green)
52 54 70 +/- 10 750 +/- 50 200 +/- 25 70,000 - 90,000
MSDS Sheets: P-50 Base, P-50 Activator Prototype - Chemical Release, Chemical Resistance, High Strength w/ Low Shrinkage - PU Foam and Self Supporting Mold Applications
Anchorseal
P-60
Tan
(Blue)
58 62 75 +/- 10 900 +/- 90 200 +/- 25 95,000 - 120,000
MSDS Sheets: P-60 Base, P-60 Activator Prototype - High Durometer, High Modulus, Heat Resistance, Epoxy and Polyurethane
Anchorseal
P-90 *
White
(Red)
32 35 125 +/- 10 600 +/- 50 600 +/- 50 40,000 - 55,000
MSDS Sheets: P-90 Base, P-90 Activator Sculpting, Foundry, Amusement Parks - Low Specific Gravity, Exceptional Flexibility and Tear Resistance - Excellent Detail Registration
Anchorseal
P-125
Translucent
(Clear)
40 40 90 +/- 15 700 +/- 50 250 +/- 50 90,000 - 110,000
MSDS Sheets: P-125 Base, P-125 Activator Prototype - Clear for Visual Inspection
Anchorseal
XP-697
Off White
(Red Brown
)
40 40 160 +/- 20 800 +/- 50 275 +/- 50 75,000 +/- 10,000
MSDS Sheets: XP-697 Base, XP-697 Activator Fast Curing, Moderate Durometer, Superb Physical Properties, Excellent Release and Good Chemical Resistance
Anchorseal
P-FDA
White
(Clear)
37 37 110 850 360 88000
MSDS Sheets: P-FDA Base, P-FDA Activator Designed for mold making where FDA requirements are needed eg, repeated food contact, making candy. Not for medical use inside the human body.
Anchorseal

Specialty Type Products

MR-15 Mold release for GI Series and Platinum series, prevents bonding of Silicone to itself
Anchorseal
GI Thinner Lowers viscosity and can softens the cured RTV. Water clear, non-reactive silicone fluid for use with GI or Platinum Series
Anchorseal

All activators are available in clear.
Standard Tin and Platinum Series mix ratio is 10 - 1 by weight, excluding P-17 Black, P-17 Black is 1:1.
All Tin Series products have a minimum of 6 month shelf life.
Tin Series products cure in 16-24 hours @ 75F.

Mixing ratio is 10 parts of Base to 1 part of Activator by weight, excluding P-17. P-17 as shown is a 1:1 ratio. Deviations from
the specified mix ratio will cause changes in the physical properties. Choose a container with a volume that is three to four times
greater than that of the rubber. Weigh the components carefully and mix thoroughly while simultaneously scraping the sides
and bottom of the container to insure that there is no unmixed portion. Place the container in a vacuum chamber and
deaerate at 28 to 29 inches of mercury vacuum until the mass of rubber rises and then collapses. Remove the mixed rubber
and carefully pour over mold, MR-15 is recommended for GI and Platinum molds.

* Translucent Base Available